jrc sprint car rules

[10 pins racing]

where can I find the sprint car rules I saw them somewhere on here. thanks:checkeredflag:

[mikejhs82]

There is a forum dedicated to the national rules....Or try under the links at the top of any page..


Hope this helps..

Mike Warner

[10 pins racing]

There is a forum dedicated to the national rules....Or try under the links at the top of any page..


Hope this helps..

Mike Warner

thanks mike
I just thought that mikes rules wee different wide chassis vs.narrow chassis

[cnyrcer]

here you go Jan...this is what they were when it started..

Rules will be simple (similar to the US Open Wheel rules):

Must have scale appearing cage, tail, hood, side panels, nerf bars, and bumpers.

Must run top wing - maximum wing surface area is 6" X 6" plus a 1/2" max rear spoiler, wing center section must be square. Left side panel max 4" x 7" max., right side panel 3.25" x 7". Front wing maximum surface area is 8 square inches with max side panels of 3" long and 1.5 " high, max of 1"above horizontal wing surface. Maximum front bumper width is 4". No lexan or any other material may be mounted to nerf bars or bumpers that may assist as an aero device.

Batteries: Any ROAR legal LiPo or 4600 mAh conventional 6-cell pack is legal.

Motors: Any ROAR stock 27t, Any fixed timing, tagged 19t, or any 17.5 or 13.5 brushless motor are all legal.

Tires: Foam tires only. No silicones. No truck foams.

[WADE ROWLEY]

looks like you can get a few more miles out of the "old car" and "driver"...:thumbsup::ha::ha::ha:

thanks mike
I just thought that mikes rules wee different wide chassis vs.narrow chassis

here you go Jan...this is what they were when it started..

Rules will be simple (similar to the US Open Wheel rules):

Must have scale appearing cage, tail, hood, side panels, nerf bars, and bumpers.

Must run top wing - maximum wing surface area is 6" X 6" plus a 1/2" max rear spoiler, wing center section must be square. Left side panel max 4" x 7" max., right side panel 3.25" x 7". Front wing maximum surface area is 8 square inches with max side panels of 3" long and 1.5 " high, max of 1"above horizontal wing surface. Maximum front bumper width is 4". No lexan or any other material may be mounted to nerf bars or bumpers that may assist as an aero device.

Batteries: Any ROAR legal LiPo or 4600 mAh conventional 6-cell pack is legal.

Motors: Any ROAR stock 27t, Any fixed timing, tagged 19t, or any 17.5 or 13.5 brushless motor are all legal.

Tires: Foam tires only. No silicones. No truck foams.

[cnyrcer]

wide chassis' and drivers are allowed...:D....was a great field of sprinters last time the series ran there...should be again for the opener..see you in a couple weeks!

[Mike Jeffery]

Thanks Bruce for clarifying the rules for everyone, now I won't have to, BTW want to be the JRC Sprint series official Tech person? Please.
Thanks,
Mike

wide chassis' and drivers are allowed...:D....was a great field of sprinters last time the series ran there...should be again for the opener..see you in a couple weeks!

[Crash#15]

Thanks Bruce for clarifying the rules for everyone, now I won't have to, BTW want to be the JRC Sprint series official Tech person? Please.
Thanks,
Mike

Bruce the tech guy yikes! lol just kidding bruce... I bet hed do a great job:thumbsup:

[cnyrcer]

Thanks Bruce for clarifying the rules for everyone, now I won't have to, BTW want to be the JRC Sprint series official Tech person? Please.
Thanks,
Mike

Mike if your serious ,I may be interested...I will give you a call..probably early next week...

[shiboy]

Mike if your serious ,I may be interested...I will give you a call..probably early next week...Whats the schedule??is it the same as last year( with the wdra tour??) any info ...

[freeloader Rob]

It will be following the mr.dirt rc series. The schedule is at www.mrdirtrcseries.com (http://www.mrdirtrcseries.com). Race 1 is March 22nd at Redneck.