New Klien replacement A-arms

[smitty]

We now have avaiable front and rear Klien A-arms.

As always they are $8.00 each and are machined out of 6/6 nylon and can be dyed.

These arms are a direct replacement for the gas sprint cars.

Thank you for your support.

Chad Smith
www.dynotech-racing.com (http://www.dynotech-racing.com)

[TrackKat]

Thanks again Chad you did a VERY nice job on them! Ill be in Oshkosh to give them the test this weekend :rolleyes:

[smitty]

Glad to hear that you liked them.

Also glad to help keep another car on the track, no matter what make.

Let me know if there is anything else I can help with.

Chad

[Smokinnitro]

do you have a part # I would like to order some

[smitty]

Klein replacement front a-arm #2701
Klein replacement rear a-arm #2700

[philipbursee]

i was tring to order a set of the klien front arms there not listed on the dynotech web page can you help me.

thanks philip

[Fast RC 007]

do you make other Klein parts?

[Ttowntoolman]

Yes, looking for Klein part here also............

[smitty]

Some of our new parts have yet to be listed on our site. E-mail with part numbers and we'll get them out to you, all arms are in stock.

Other parts?? What are you looking for, we can make it.

Let me know.

Chad Smith
www.dynotech-racing.com (http://www.dynotech-racing.com)

[Fast RC 007]

Some of our new parts have yet to be listed on our site. E-mail with part numbers and we'll get them out to you, all arms are in stock.

Other parts?? What are you looking for, we can make it.

Let me know.

Chad Smith
www.dynotech-racing.com (http://www.dynotech-racing.com)


How about...

1. carbon fiber front and rear shock towers, slight shock mounting hole change.
2. dyeable delrin front bulkhead, modified for adj kickup, lightened
3. carbon fiber tranny case support.
4. carbon fiber chassis plate, left side batt, drilled to fit Dynotech cage and body.

A Klein conversion into a KleinotechCW

Let me know if you are intested, maybe I can help with drawings.

007

[smitty]

Drawings, sample parts, just let me know.

Chad Smith
www.dynotech-racing.com (http://www.dynotech-racing.com)

[Fast RC 007]

Drawings, sample parts, just let me know.

Chad Smith
www.dynotech-racing.com (http://www.dynotech-racing.com)


Thanks Chad, I will, but I'm not ready to pull the trigger just yet. When I am tho, what kind of lead time do you need typically?

[smitty]

Two to three weeks on average, unless I have some pressing things to get done.

[Fast RC 007]

Sounds good, thanks. :thumbsup:

[scr8p]

i'm interested in getting a set of these arms for a custom build. could someone give me the length measurements from center hinge pin to center hinge pin? maybe a pic, too? fronts and rears. any help would be appreciated.

thanks in advance.

[TrackKat]

I measured:

Fronts 2.440"

Rears 2.537"

hope this helps

[scr8p]

thanks trackkat. :D

[TrackKat]

No problem :thumbsup: what are you building?

[scr8p]

well, i guess it's not really a "custom" build, but i wanted to know if they were the same dimensions as the old rpm worlds conversion arms. since those are impossible to find.

do the dynotech arms come in white from new? did you dye yours black?

[TrackKat]

Yes :thumbsup:

[scr8p]

cool. one more question for ya trackkat. the klein front arm mounts. are they like a standard rc10 buggy mount, or more like a 10t/gt front bulkhead? width wise. where the front inner hinge pin goes through.

[olderacer]

they fit the 10t/gt front bulkhead. they are like the rpm worlds arms but a little longer. if you use klien front arms and rc10 rears your front will be wider than your rear. if you use klien rear arms replace the dogbone with one from the b4. we have a rc10 latemodel class locally and since i didn't have a rc10 but had a 10t with oval towers i picked up the front and rear klien arms to turn my 10t into a car. worked very well. thank you dynotech for making these replacement arms for the kliens and other cars using these arms.

[Smokinnitro]

thats exactly what i use for my nitro latemodel but with a Barts truck chassis. I'd like to try a Leake chassis and run a customworks front end.