Get Back chassis ?

[corcarbill]

Looking for info on the Get Back chassis kit.

[Stetler17]

Bill,

I can't find the number anymore. He goes by Taylor8 on here.

[TQT2]

Try calling REDNECK RC...their phone number is; 315-532-6826

or try contacting them via the website....http://www.redneckrc.com/contact.aspx

This Sunday they had only 4 chassis left and yes, you will need the steering parts with it.



Keith D

[corcarbill]

Thanks :tire:

[Oval-Man]

Looking for info on the Get Back chassis kit.You have a PM

[Higman Racing]

what is this chassis for?

[JTRAIN]

It is another chassis option for the b3 terminator based cars.

[RCRACR20]

Redneck RC is the "official distributor" of the Getback RC products. We currently have the chassis, front and rear shock towers, motor plate, delrin steering bellcranks (required with use of this chassis) and both flavors of traction compound. I will get pictures ASAP. Try giving Redneck RC a call at 315-532-6826

[hotshoe8t]

here are a few pics of a Get Back Chassis conversion for a B3 Terminator. RCRACR20 should be able to get you guys a few pics of the products and parts they have in stock currently. If not I will get a few a post them. As stated above Redneck R/C is the official distributor of our chassis and all Get Back R/C products.

[wait a minute]

is that a new tech tip i see on the rear axel..using a body clip to hold the axel in place?:D

[hotshoe8t]

you mean axle? I could try to explain it to you, but I'm not sure you would understand.:D

[RCRACR20]

I will try to get some pictures tomorrow.

[glgraphix]

Oh, now thats just Smoken ! ! Now, I want a Term for sure. How much are these? Might just have to build another car??!!!
Kevin

[RCRACR20]

Chassis $70
Bellcranks (required) $20
Front Shock Tower $15
Rear Shock Tower $20
Motor Plate $20

Conversion kit $140

[corcarbill]

Chassis $70
Bellcranks (required) $20
Front Shock Tower $15
Rear Shock Tower $20
Motor Plate $20

Conversion kit $140

YGPM
:tire:

[RCRACR20]

Bill, I PM'd you with a total and the shops paypal addy.


Matt

[RCRACR20]

Here are the pictures I took this afternoon of all the Getback RC products. We actually sold out of chassis this afternoon and will have more in stock the beginning of next week. Please email me at matto29@yahoo.com, or call the shop at 315-532-6826 if you have any questions.

Matt

[RCRACR20]

heres the rest of them:

[latemodel13]

Hey Bill I'll have to call you get to the back Bill!

[doctorj]

http://by143fd.bay143.hotmail.msn.com/cgi-bin/saferd/Image012%2ejpg?_lang=EN&hm___tg=http%3a%2f%2f65%2e55%2e154%2e124%2fcgi%2db in%2fgetmsg%2fImage012%252ejpg&hm___qs=%26msg%3dA5DF8F9F%2d9523%2d4511%2dA719%2dB 43F2D6C667C%26start%3d0%26len%3d37724%26mimepart%3 d2%26curmbox%3d641C53F7%2d0947%2d448C%2d87F5%2d299 A052F2667%26b%3d9e97ecece2ce60910e5d9920ce24f089%2 6disk%3d10%2e1%2e106%2e118_d2357%26login%3djunior_ barnes11%26domain%3dhotmail%252ecom%26_lang%3dEN%2 6country%3dUS&hm___cacheh=1&file=Image012%2ejpg&domain=hotmail.com

[Bulldog_Wally14]

Does the bell crank set come w/ the bushings (posts)?

[solly]

Does the bell crank set come w/ the bushings (posts)?

no

[RCRACR20]

That is correct, you will still need Steering bellcrank posts.

[DanTheEbayMan]

How long will it be before we can get the COMPLETE $140 kit? I WANT one!!

[RCRACR20]

Dan, We are hoping to have them back in stock this weekend.

[doctorj]

talked to chico today... he was busy cutting chassis, so i'm betting that the parts will be in stock soon. he said he's workin on a new and improved shock tower. can't wait...moving forward is what GETBACK is all about!!

[DL3]

very nice pieces , might have to get me one of those .....

[hotshoe8t]

New steering bellcranks will now come with the standoff posts. Pricing on the Bellcrank kits will now be $25. Also as stated above, Chico now has a new designed rear shock tower with more adjustment built into it. I will get some pictures of these parts asap for you guys.


That is correct, you will still need Steering bellcrank posts.

[DanTheEbayMan]

Let the BUILD BEGIN...

[DanTheEbayMan]

Dan, We are hoping to have them back in stock this weekend.


Ok Great, GOT It. Thanks...

What's the best SMALL SIZE servo for the chassis? Price? and do you have one IN STOCK?

My Spektrum Z590 Servo is to big to fit the front of the chassis...

[Oval-Man]

Ok Great, GOT It. Thanks...

What's the best SMALL SIZE servo for the chassis? Price? and do you have one IN STOCK?

My Spektrum Z590 Servo is to big to fit the front of the chassis...Dan, Use the futaba 9650, it fits perfect.

[hotshoe8t]

As Jeff stated a 9650 is the best servo to use,digital servo that is super smooth and quick. One other servo that i know of that fits well is a Hitec HS225 ,it's a touch slower and not digital, but works fine. I run one in both of my cars. They retail for around $20 to $25 as where the Futaba 9650 generaly goes for around $50-60.

[RCRACR20]

Ok Great, GOT It. Thanks...

What's the best SMALL SIZE servo for the chassis? Price? and do you have one IN STOCK?

My Spektrum Z590 Servo is to big to fit the front of the chassis...

Dan,

Futaba 9650 or 9602


Matt

[DanTheEbayMan]

Let the BUILD BEGIN...Continued...


Here is another pic of the car and the ALMOST COMPLETE stage...

[TQT2]

So Dan, about that transponder placement....lemme tell ya a lil story about that. Not to long ago, Jack won a race that had me clearly finishing ahead of him, yet because my transponder is on the servo, whereas his in nose of the Sprinter....he beat me by .00's of a second.

Mind you I don't mind losing a race that close...and as fun as it was, yet just a thought for ya and your servo tape....yeah, why do they call it servo tape anyways when people actually mount their servos???? :confused:

Keith D

[hotshoe8t]

the personal transponder would be a little more prone to being damaged in the nose section of an EDM. With the sprints you at least have a cage piece to kinda protect it a little. Under the lexan in front of the tower may not offer too much damage protection. I have seen a few guys that run them there, but not many. Kinda a personal preference I guess. Where you have it Dan is exactly where me,Chico and most of the guys running our cars have them placed, have not seen any problems with them being damaged or anything there yet. Anyhow,the car looks good Dan, now take it over there and lay it on Hilts.

[hotshoe8t]

also here is a pic of our new shock tower. It is quite abit wider than the previous tower we had been using and also a little lighter. Dan has one of the new towers on his car pictured above also.

[DanTheEbayMan]

also here is a pic of our new shock tower. It is quite abit wider than the previous tower we had been using and also a little lighter. Dan has one of the new towers on his car pictured above also.


I like it too. It gives me more positions to make shock adjustments with. WAY better than
the stock shock tower...

[DanTheEbayMan]

So Dan, about that transponder placement....lemme tell ya a lil story about that. Not to long ago, Jack won a race that had me clearly finishing ahead of him, yet because my transponder is on the servo, whereas his in nose of the Sprinter....he beat me by .00's of a second.

Mind you I don't mind losing a race that close...and as fun as it was, yet just a thought for ya and your servo tape....yeah, why do they call it servo tape anyways when people actually mount their servos???? :confused:

Keith D


Hey Keith,
I was going to use SERVO TAPE but the servo saver would have hit the chassis. So I ACTUALLY had to mount it....

NOW If I could just find a place for the ESC that I LIKE...

[hotshoe8t]

Dan, what speed control are you using? Most guys with these chassis are using the Hara twister,LRP Q2 or Novak GTX variants. As long as it fits there, mount it on the pad for the speed control or you can mount it right behind the receiver on the left side of chassis. Either way make sure you use some kinda clip or something to keep the wiring off the chassis. I use simple wire retainer clips from Radio Shack, beleive Redneck also carries the CRC brand also. As for location it doesn't really seem to affect the handling either place you put the speed control.

[pancartom]

what's the status of the conversion kits? do you guys have them?

[DanTheEbayMan]

Dan, what speed control are you using? Most guys with these chassis are using the Hara twister,LRP Q2 or Novak GTX variants. As long as it fits there, mount it on the pad for the speed control or you can mount it right behind the receiver on the left side of chassis. Either way make sure you use some kinda clip or something to keep the wiring off the chassis. I use simple wire retainer clips from Radio Shack, beleive Redneck also carries the CRC brand also. As for location it doesn't really seem to affect the handling either place you put the speed control.


Hello Chris,
Using a Novak GTX Controller, I put the ESC in FRONT of the Rear LEFT Wheel as far LEFT as I could. Used small zip ties to control the wireing. Worked great. Just have to make a small
guard to keep the dirt / grease off of the ESC.

[RCRACR20]

what's the status of the conversion kits? do you guys have them?

Tom, we have them. Ill be going to the shop tomorrow to package your kit up. Ill send you a PM a little later today when I have a break from classes.

[pancartom]

thanks, Matt. I'm going to send you a PM about other stuff too.

[Stetler17]

JR's new 3650 servo also fits very nicely on the GetBack chassis.

Very similar specs to the Futaba but with metal gears instead of plastic.

I run mine without a servo saver for a really clean looking installation. Works great.

What's with the cutout battery slots? My 4200's fit this chassis better than any other I've had with the original six slots intact. Weight???

[RCRACR20]

lower center of gravity

[Stetler17]

What am I missing? Wouldn't the material that's still there hold the battery at the same height? Unless your cutting the slots a lot wider, which appears they aren't.

Thanks for any info.
Mark

[doctorj]

stetler17,
the battery slots were done over so the batteries would be sitting lower in the chassis, the original 6 slots weren't bad at all... but the big three let it sit lower and also let more tape stick to the cells and help keep em in the car!!

hey chris... get her back together yet? that sure was a narly crash... i don't think there was a car in that heat that didn't hit your sitting duck. i'll bet this is what we looked like on the drivers stand- :o :D :confused: :(

[hotshoe8t]

yes, she's like new still, the only thing it broke off was a camber link on the LF. I could have fixed it easily, but I just wasn't really into it last week for some reason.

Stetler17, exactly as Doctorj above on the slots, lower CG and to let the tape stick to more of the cells.

[tfelog]

Matt, you have a pm
-Ryan

[MiniT21]

sorry for the noob question, but you guys say b3 terminator, Is that a CW based kit? or is this a conversion for the b3?

[RCRACR20]

Ryan, got your conversion packaged up, it will be sent Monday morning.

MiniT21, This chassis conversion is one of many for the Kranzel Terminator, which is a conversion for the RC10B2/B3. All the Kranzel, JRC, OHP/Go-Fast, and Putnam components are compatible with the Getback Conversion. If you have any questions, please feel free to call the shop or shoot me a PM.